合肥叉车水箱高温的影响因素有哪些？

叉车浅谈引起内燃叉车水箱高温的原因及解决办法： 驾驶员都知道，有时候，尤其在夏天，内燃叉车的水箱会有很高温的时候，必须停下来，这样就影响了叉车作业，严重时还会损坏零部件，那有哪些原因引起叉车水箱高温的呢?该如何解决呢?叉车通知你：
forklift brief talk about the causes and solutions of high temperature in water tank of internal combustion forklift truck: drivers know that sometimes, especially in summer, when the water tank of internal combustion forklift truck will have a high temperature, they must stop, which will affect the operation of forklift truck, and even damage parts in serious cases. what causes the high temperature in water tank of forklift truck and how to solve it?
叉车水温过高的原因
reasons for excessive water temperature of forklift trucks
水温高有许多原因：控温开关、泵、子扇、水管锈了、回水不好等因素都会引起这样的结现象。发动机水温的凹凸主要是和节温器是否正常作业、水泵能否建立满足的压力、冷却电扇能否到达规范转速有关。那如何来查看叉车水温不正常呢?冷却系统一般由冷却电扇、散热器、节温器等元件构成。冷却电扇往往由发动机直接带动，而且电扇转速与发动机转速一致。冷却水温的控制主要依靠节温器。
there are many reasons for the high water temperature: temperature control switches, pumps, fans, rusted water pipes, poor backwater and other factors can cause such knot phenomenon. the concave and convex of engine water temperature is mainly related to whether the thermostat is working properly, whether the pump can establish the satisfied pressure, and whether the cooling fan can reach the standard speed. how to check the temperature of forklift truck is abnormal? cooling system is generally composed of cooling fans, radiators, thermostats and other components. cooling fans are often driven directly by the engine, and the speed of the fan is the same as that of the engine. the control of cooling water temperature mainly depends on thermostat.
节温器的原理
principle of thermostat
节温器又称调温器，功用是根据冷却水温度的凹凸主动调理进入散热器的水量，改动水的循环规模，以调理冷却系的散热才能，确保发动机在适宜的温度规模内作业。节温器必须保持杰出的技术状况，否则会严重影响发动机的正常作业。如节温器主阀门开启过迟，就会引起发动机过热;主阀门开启过早，则使发动机预热时刻延伸，使发动机温度过低。此刻可判别节温器的作业状况是否杰出，当发动机开端冷车作业时，水箱的上水室进水管处如还有冷却水流出，则阐明节温器的主阀门不能关闭;当发动机冷却水温度超越70摄氏度时，水箱的上水室进水管处无冷却水流出，则阐明节温器主阀门不能正常开启，这时就需要进行修理。
the function of thermostat is to actively adjust the amount of water entering the radiator according to the concave and convex temperature of cooling water, to change the scale of water circulation, to adjust the cooling capacity of the cooling system, and to ensure that the engine works in the appropriate temperature scale. the thermostat must maintain outstanding technical condition, otherwise it will seriously affect the normal operation of the engine. if the main valve of the thermostat is opened too late, the engine will be overheated; if the main valve is opened too early, the preheating time of the engine will be extended and the temperature of the engine will be too low. at this moment, we can judge whether the operation of thermostat is outstanding or not. if there is cooling water flowing out from the inlet pipe of the water tank at the beginning of the cold car operation, we can clarify that the main valve of the thermostat can not be closed. when the cooling water temperature of the engine exceeds 70 degrees celsius, there is no cooling water flowing out from the inlet pipe of the water tank, we can clarify that the main valve of the thermostat can not be opened normally. repair is needed.
节温器的查看可在车上进行，办法如下：
the thermostat can be checked in the car by the following methods:
一、发动机起动后的查看：翻开散热器加水口盖，若散热器内冷却水安静，则标明节温器作业正常，否则，则标明节温器作业失常。
1. view after engine start: open the radiator plus nozzle cover. if the cooling water in the radiator is quiet, it indicates that the thermostat works normally, otherwise, it indicates that the thermostat works abnormally.
二、这是因为，在水温低于70℃时，节温器胀大筒处于缩短状况，主阀门关闭;当水温高于80℃时，胀大筒胀大，主阀门渐渐翻开，散热器内循环水开端活动。
2. this is because when the water temperature is lower than 70 c, the expanding cylinder of the thermostat is in a shortening state and the main valve closes; when the water temperature is higher than 80 c, the expanding cylinder expands, the main valve gradually opens, and the circulating water in the radiator starts to move.
三、当水温表指示70℃以下时，散热器进水管处若有水活动，水温温热，则表时节温器主阀门关闭不严，使冷却水过早大循环。
3. when the w